Weltneuheit: Anhänger EEG mit Funkübertragung in PC zur BioexplorerSoftware der wohl weltweit besten EEG Biofeedbacksoftware !!! Nur 799.- Euro Hammerpreis Kopfhaube + Elektroden 119.-
Technische Daten: 2 ch EEG, User-selectable Bandwidth 40/48/56 Hz , User-selectable Sampling 122/128/256/512sps by downloading profile 12-bit; 1.5mm 2ch bipolar montage connector , Wireless Technology: USB wireless dongle Charger battery, 1.5mm Touchproof electrodes, Concurrent wireless chs 8 , (user supplied) ; 2.4GHz / 3m, "BioExplorer" PC-based neurofeedback (supports all products) Download trial
BioExplorer Software 399.-€ Demo : http://www.cyberevolution.com/download.htm
Spectrum Analyzer in 3D mode
Spectrum Analyzer in CSA mode
Spectrum Analyzer in Bins mode
Spectrum Analyzer in Spectrogram mode
Two Spectrum Analyzers configured as a bilateral spectrum display
Oscilloscope, Bar Graph, and Meter with thresholds
Spectrum Analyzer settings
Bandpass Filter settings
Instruments window in Edit Layout mode
The real power of BioExplorer comes from the ability to connect signal processing and display objects any way you want.
The following objects are available for use in the Signal Diagram:
The output is the logical AND of two or more signals
Plays audio files (mp3, wma, wave, midi, etc.) Volume and Play/Pause can be controlled by one or more signals.
Calculates the average value of a signal over a specified time period.
Filters a signal, allowing frequency components that are between the low band edge and the high band edge to pass through, and attenuating components outside this range. Outputs the filtered signal as well as the amplitude of that signal.
Graphically indicates the current value of a signal.
Allows you to manually set the state of a signal.
Plays audio CDs. Volume and Play/Pause can be controlled by one or more signals
Calculates the coherence between two signals.
Plays a continuous MIDI note. Volume, Pitch, and Play/Pause can be controlled by one or more signals.
Calculates the correlation between two signals.
Counts properties of a signal (rising edges, falling edges, time high or time low).
Outputs the difference between the current sample and the previous sample.
Calculates the dominant frequency (the frequency component with the largest amplitude) of a signal.
Plays DVDs. Volume and Play/Pause can be controlled by one or more signals
Uses a user-defined expression to calculate the output based on one or more signals, e.g. '( In2 - In1 ) / (In1 + In2 )'.
Outputs the maximum value of a signal.
Calculates the mean frequency in a given bandwidth.
Indicates the current value of a signal.
Plays musical notes at a periodic rate. The volume, note, and timing can be controlled by one or more signals.
Outputs the minimum value of a signal.
The output is the logical NOT of a signal.
The output is the logical OR of two or more signals.
Displays one or more signals over time.
Calculates the ratio of the power in two frequency bands, or the percent of the total power contained in one frequency band of a signal.
Given an EKG signal, determines the current pulse rate.
This object represents a channel on a device (e.g. BrainMaster channel 1, etc). Source objects are used to get data from a device into the Signal Diagram.
Displays the spectrum of a signal. Currently supports four different modes: spectrogram (shown below), bins, compressed spectral array, and 3D.
Calculates the Standard Deviation and Mean of a signal over a specified time period.
This object compares a signal to a threshold. You can set the threshold manually or have the object adjust it automatically based on characteristics of the signal.
Generates an audio tone. Frequency, Volume, and Play/Pause can be controlled by one or more signals.
Displays the mean value of one or more signals over a user specified time period (e.g. 10 minutes). New data is added to the right side and the display scrolls to the left, so the last 'x' amount of time is always visible.
Plays video files (mpeg, wmv, avi, etc.) Volume and Play/Pause can be controlled by one or more signals